Part-level entry
Start from the part that has to hold, not from the tape name.
Every row below is a part on a real assembly: a duct joint, a battery terminal, a display bezel, a coil, a floor seam. Each one lists what usually fails there and which tapes come back on the short list, with the level of confirmation we can give before a sample.
Inputthe part and the failure mode
Outputshort list + confirmation level
Next stepsample on the real surface
26 part-level cases A short list is a screening result, not a specification. Numeric values only come with the approved datasheet for the ordered lot.
| Part / task | What usually fails | Short list | Confirmation |
|---|---|---|---|
| HVAC duct & insulation-joint sealing | Air tightness, moisture, temperature cycling | Recommended | |
| Roof, solar-panel & pipe repair sealing | Water ingress, UV, uneven surface | Recommended | |
| Vapour barrier & protective wrapping | Moisture transmission, overlap, site damage | Recommended |
| Part / task | What usually fails | Short list | Confirmation |
|---|---|---|---|
| Wire harness wrapping | Abrasion, rattle and noise, bundle retention | Quote only Harness tape is specified by the harness standard of the vehicle programme, so it is quoted per project rather than stocked as a catalogue grade. | Quote only |
| Battery insulation & terminal protection | Electrical isolation, thin profile, electrolyte exposure | Polyimide Electrical Insulation Tape Recommended Polyester High-Temperature Masking Tape Recommended Thermally Conductive Interface Tape Spec confirmation Conductive Fabric Shielding Tape Spec confirmation Terminal-level parts are usually die-cut to drawing with a defined creepage path. | Recommended |
| Interior trim, badge & component mounting | Surface bonding, temperature/humidity cycling, vibration | Recommended |
| Part / task | What usually fails | Short list | Confirmation |
|---|---|---|---|
| Transformer, motor & coil insulation | Insulation coverage, heat resistance, edge lifting | Recommended | |
| PCB soldering, coating & plating masking | Edge bleed, residue, removal effort | Recommended | |
| Powder coating & heat-transfer masking | Repeated high-temperature cycles, edge definition, surface condition | Masking boundary under repeated cure cycles needs a trial on the real part before it is committed. | Engineering evaluation |
| FPC, cable & flex-circuit fixing | Thin profile, flexing, rework | Reworkable holding and converted shapes are handled as a drawing-based part, not as a catalogue roll. | Recommended |
| Temporary protection for electronic parts | Scratch, contamination, ESD and residue | Recommended | |
| LED strip & panel mounting / thermal bonding | Heat path, fixing strength, electrical isolation | Recommended | |
| Optical display bonding | Transmittance, haze, bubble | Recommended | |
| Lens and bezel light blocking | Light leakage, reflection, appearance | Spec confirmation | |
| Display panel temporary protection | Scratch, dust, residue after removal | Recommended |
| Part / task | What usually fails | Short list | Confirmation |
|---|---|---|---|
| Heat-sealer anti-stick & wear protection | Sticking, wear, tape changeover frequency | Recommended | |
| Tooling, fixture & temporary holding | Positioning, clean removal, repeat stability | Quote only Holding force, removal mode and cycle life decide the grade; the construction is chosen against the fixture drawing. | Quote only |
| Fiberglass-reinforced holding & bundling | Tensile strength, tear resistance, retention | Recommended | |
| Equipment & appliance shipping protection | Scratch, impact, residue | Recommended | |
| 5S workcell and floor positioning | Recognition, floor adhesion, abrasion | Quote only Floor marking is quoted against the floor finish and traffic load on site. | Quote only |
| Facility warning & safety marking | Boundary legibility, low-light visibility | Spec confirmation | |
| Industrial anti-slip | Wet slip resistance, wear, walking comfort | Engineering evaluation |
| Part / task | What usually fails | Short list | Confirmation |
|---|---|---|---|
| Roll splicing & web joining | Splice thickness, tension, web break | Recommended | |
| Carpet, floor-covering & temporary joining | Seam visibility, removal, floor condition | Recommended | |
| Resealable & tear-strip package closure | Reopen behaviour, retention, material compatibility | Recommended | |
| Custom die-cut & laminated parts | Tolerance, cycle time, multi-layer release | Quote only Drawing-based part: the layer stack, registration and release liner are confirmed before a quote. | Quote only |
One tape, several fields.
Most grades are not built for a single industry. The same backing and adhesive solve a duct joint, a battery terminal and a converting line, with the confirmation level changing per part. This is the reverse view of the table above.
17 of the 29 grades in this table serve more than one industrySend the part description
Fill what you know. The form opens your mail client with the answer already written, so we can reply with a grade and a confirmation level instead of a question list.